泰拉瑞亚维基:电脑各种中英文信息对照及错误信息总汇之一
来源:百度文库 编辑:偶看新闻 时间:2024/09/28 07:43:47
电脑各种中英文信息对照及错误信息总汇之一
(2010-04-05 11:07:52) 转载▼标签:it
分类: 共享资料一、BIOS中的提示信息
提示信息
Drive A error
System halt
Keyboard controller error
Keyboard error or no keyboard present
BIOS ROM checksum error BIOS ROM
Single hardisk cable fail
FDD Controller Failure BIOS
HDD Controller Failure BIOS
Driver Error
Cache Memory Bad, Do not Enable Cache
Error: Unable to control A20 line
Memory write/Read failure
Memory allocation error
CMOS Battery state Low
Keyboard interface error
Hard disk drive failure
Hard disk not present
Floppy disk(s) fail (40)
CMOS checksum error-efaults loaded.
二、BIOS刷新失败后,Bootblock启动时出现的提示信息
提示信息
Detecting floppy drive A media...
Drive media is : 1.44Mb1.2Mb 720Kb 360K
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
三、MBR主引导区提示信息
提示信息
Invalid partition table
Error loading operating sy stem
Missing operating system
说明:如果在计算机启动过程中,在硬件配置清单下方(也就时在平时正常启动时出现Starting windows 98…的地方)出现不可识别字符,此时可判断硬盘分区表损坏。如果你的硬盘上有重要资料,这时你不要轻易进行分区,可找专业的数据恢复公司。
四、DOS活动分区中的提示信息
提示信息
Invalid system disk
Disk I/O error, Replace the disk and press any key.
Invalid Media Type reaching Drive C:
Invalid Boot Diskette Boot Failure
五、IO.SYS中的提示信息
提示信息
Insert diskette for drive and press any key when ready
Your program caused a divide overflow error
If the problem persists, contact your program vendor
windows has disabled direct disk access to protect your long filenames windows
The system has been halted. Press Ctrl+Alt+Del to restart your computer
You started your computer with a version of MS-DOS incompatible with this version of windows. Insert a Startup diskette matching this version of windows and then restart
This version of windows requires a 386 or better processor 该Windows版本需要386以后的CPU支持
A20 hardware error. Contact technical support to identify the problem
Starting windows 98...
windows 98 is now starting your MS-DOS-based program
windows 98 is now restarting...
Press Esc now to cancel MS-DOS mode and restart windows 98...
There is an unrecognized command in your CONFIG.SYS file
The following command in your CONFIG.SYS file is incorrect:
The sector size specified in this file is too large:
The following file is missing or corrupted: WIN.COM COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file
There is an error in the COUNTRY command in your CONFIG.SYS file
There is not enough memory for the COUNTRY.SYS file
Remove some drivers from your CONFIG.SYS file, and then try again
Remove some drivers, and then try again
Remove some disk drivers from your CONFIG.SYS file, and then try again
The configuration specified in your CONFIG.SYS file is too large for memory
You have too many block devices specified in your CONFIG.SYS file
The STACKS setting(s) in your CONFIG.SYS file are incorrect
Default stack settings will be used instead
There is an error in your CONFIG.SYS file on line XX
Warning: Logical drives past Z exist and will be ignored
Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) Press any key to continue…
windows is bypassing your startup files
Minimal network support will be loaded if available windows
windows is starting the command prompt only
windows will prompt you to confirm each startup command
The compression driver cannot be set up correctly
Get a version from your vendor that is compatible with this version of windows
Process the system registry
Create a startup log file (BOOTLOG.TXT)
Process your startup device drivers (CONFIG.SYS)
Process your startup command file (AUTOEXEC.BAT)
Load the windows graphical user interface
Warning: windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG
Warning: windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem
Warning: windows did not finish loading on the previous attempt. Choose Safe mode, to start windows with a minimal set of drivers
Warning: windows multi-boot may not function correctly
Check for system files in your root directory with conflicting extensions
Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly
The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS里BUFFER设置太大。默认的BUFFER缓冲器设置将被使用