zuk z2拨号代码:包装盒图纸
Four Corner Beers Tray (a.k.a.) Biers
The Beers tray is glued by the converter and shipped flat to the user. It is typically set up and loaded by hand. Figures 1 and 2 show the conventional Beers. Fig. 3 shows the "stay-up" or "ull drag" version. The combination of an end panel diagonal angle of less than 45° (431/2° typically) and a non-tapered glue flap causes the glue flap to "drag" across the bottom panel. Natural friction causes the carton to resist collapsing once erected.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2101
附件:
2007/12/9 17:54
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Infold/Outfold Tray
The Infold/Outfold Tray is glued by the converter and shipped flat to the user. It is typically hand erected and loaded. Fig. 3 shows the style folded and glued as in infold. Fig. 4 shows the same style folded and glued as an Outfold. A typical commercial use would combine an Outfold bottom (easy to load) with an Infold lid (because it collapses inwardly to cause a good friction fit between the lid and base).*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2102
附件:
2007/12/9 17:57
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Four Corner Beers with Top Tuck Closure (a.k.a.) Biers
This style is typically set up, loaded and closed by hand. It is suitable for a broad range of relatively light products.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2103
附件:
2007/12/9 18:02
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Six Corner (Point) Beers (a.k.a.) Biers
The Beers is glued by the converter and shipped flat to the end user. It is typically set up and loaded by hand. Refer to the four corner Beers for alternative corner flap configurations.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2104
附件:
2007/12/9 18:07
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Stripper Lock Tray
This is a machine erected and locked style. There are a number of lock variations and also numerous equipment suppliers.
As best seen in Fig. 2, the male lock is "stripped" through the female locking slot. The upper tip of the lock extends above the upper edge of the locking slot.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2105
附件:
2007/12/9 18:34
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Stripper Lock Tray With Hinged Cover
This is a machine formed and closed style. The cover tuck and charlottes are either heat or adhesively sealed to the tray front and side panels.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2106
附件:
2007/12/9 18:40
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Four Corner Brightwood Tray
The Brightwood style is shipped flat and non-glued. It is machine formed and glued on automatic packaging equipment by the customer.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2107
附件:
2007/12/9 18:49
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Six Corner Brightwood Tray
The six corner Brightwood is shipped flat and non-glued. It is machine formed and glued on automatic packaging equipment by the customer.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Single Endwall
Style ID: 2108
附件:
2007/12/9 18:54
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Pinch Lock Tray
The Pinch Lock Tray is erected and locked by hand. Fig. 1 shows the more common single corner flap variation. Fig. 3 shows a bellows corner variation.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Double Endwall
Style ID: 2201
附件:
2007/12/9 19:00
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Walker Lock Tray
The Walker Lock Tray is typically erected and locked by hand.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Double Endwall
Style ID: 2202
附件:
2007/12/9 19:21
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Arthur Lock Tray (a.k.a.) Jones Lock Tray
The Arthur Lock tray is hand erected and used primarily as a component of a wholesale package. It is seldom seen as a retail package.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Single Sidewall/Double Endwall
Style ID: 2203
附件:
2007/12/9 19:39
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Foot Lock Double Wall Tray
This style requires a larger blank than the commonly used double side-wall/double endwall Simplex style (Style 2302) but it does not require a finishing pass over a straight line gluer as does the Simplex. This is typically a hand set up style. Fig. 1 shows the single corner flap variation. Fig. 3 illustrates a bellows corner option.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Double Sidewall/Double Endwall
Style ID: 2301
附件:
2007/12/9 19:43
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Simplex (a.k.a.) Kwikset
The sidewalls of the Simplex are preglued by the converter. It is typically hand erected by the user but it can be machine formed as well. Fig. 1 shows the most common form of the Simplex. Fig. 3 illustrates an alternative frequently used in shallower depths. As best seen in Fig. 2 the inner side panel is not as wide as the outer side panel.*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Double Sidewall/Double Endwall
Style ID: 2302
附件:
2007/12/9 19:50
2006/12/1 11:05所属群组:
注册会员 帖子: 63 等级: 6; EXP: 82
HP : 0 / 145
MP : 21 / 1035
2007/12/9 19:54
2006/12/1 11:05所属群组:
注册会员 帖子: 63 等级: 6; EXP: 82
HP : 0 / 145
MP : 21 / 1035
2007/12/9 19:59
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Simplex Tray With Glued Gussets
This is a Simplex (Kwikset) with extended gusset flaps. These extended flaps provide a target for straight line or spot application of adhesive to secure the gussets to the inside surface of the outer end panels. Gluing the corner tab assists in carton erecting, adds corner strength and contributes towards a more finished corner appearance when compared to the conventional Simplex (Style 2302).*
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Double Sidewall/Double Endwall
Style ID: 2303
附件:
2007/12/9 19:59
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Rigidwall Tray
The Rigidwall is a good alternative to the Simplex double wall tray in the shallower depths.
As best seen in Fig. 3, the sidewalls are infolded. The foot off the base of the inner side panel is glued to the bottom. A slight triangulation caused by a reduction in the depth of the inner side panel resists the outward bowing tendency of most shallow depth trays.
Category: Trays
Description: Component Parts and detailing for a Tray
Subcategory: Trays, Double Sidewall/Double Endwall
Style ID: 2304
附件:
2007/12/9 21:07
2006/10/21 11:50来自 北京100027-19信箱所属群组:
网站管理员 帖子: 3357 等级: 44; EXP: 83
HP : 876 / 1095
MP : 1119 / 8153
Double Anchor Lock, No Depth Folder
This is typically a hand loaded and closed carton. It may be used as shown here or with a film window added to the bottom panel.*
Category: Specialties
Description: Component Parts, Detailing for Specialty Packaging
Subcategory: Specialty Folders and Envelopes
Style ID: 4101
附件: